反对称铺层碳纤维复合材料圆柱壳的双稳态应力特性

双稳态复合材料可广泛应用于各类可变结构的设计。针对反对称铺层的圆柱壳,利用有限元软件ABAQUS的Standard准静态分析,模拟其双稳态跳变过程和跳回过程,探讨在整个连续过程中圆柱壳上的应力分布情况,以及应力随时间和载荷变化的趋势,从而对该类可变结构的设计起到指导作用。结果表明:该类复合材料圆柱壳跳变过程中最大应力出现在载荷施加点与约束点附近,第二稳态下应力关于板中心呈中心对称分布,最大应力沿板壳对角线出现在四个角内侧附近,而跳回过程中应力由第二稳态下的分布慢慢变为集中在约束点附近。而且整个圆柱壳上的最大应力时刻与最大载荷施加的时刻不重叠,具有滞后性。     

Experimental investigation for machinability aspects of graphene oxide/carbon fiber reinforced polymer nanocomposites and predictive modeling using hybrid approach

This article explores the drilling behavior of polymer nanocomposites reinforced by Graphene oxide/Carbon fiber using a hybrid method of Grey theory and Principal component analysis (GR-PCA). An online digital dynamometer was employed for the evaluation of Thrust Force and Torque. The image processing technique computes the delamination. Response surface methodology (RSM) considers the parameters, namely, drilling speed (S), feed rate (F), Graphene Oxide wt.% (G) in designing the experimentation array. Principal component analysis (PCA) was used to tackle the response priority weight during the combination of multiple functions. Analysis of variance (ANOVA) scrutinized the influence of parameters and intended the regression models to predict the response. GR-PCA evaluated the optimal parametric setting and remarked that feed rate acts as the most predominant factor. The higher feed rate and wt.% of G is responsible for surface damages like fiber pull-out, fiber fracture and cracks. A significant improvement in drilling responses has been obtained and also validates through confirmatory test and microstructure investigations.     

基于应变测量法的几种典型悬臂梁的挠度测量

挠度变形是工程梁设计中的一项重要指标,为了更加准确地测量梁的挠度变形,提出了采用应变式传感器进行挠度测量的方法对几种典型的悬臂梁的挠度进行测量,该方法是利用挠度与外载荷(外力偶)、弯矩与应力、应力应变之间的关系,导出梁的挠度与应变之间的关系,从而由测得的应变得出悬臂梁在外载荷作用下的挠度。测量结果表明该测量方法测得的结果大大地提高了挠度测量精度。     

基于磁通门/GPS组合的车辆导航系统滤波技术

给出了基于磁通门/GPS组合导航系统的硬件结构图,并应用卡尔曼滤波和方差自适应滤波算法分别对GPS、磁通门单独导航定位系统进行了分散滤波,最后应用联合卡尔曼滤波器对GPS和磁通门信息进行了信息融合.并且通过实际跑车实验,验证了滤波对导航系统随机误差消除和定位精度提高的有效性.     

基于PON技术的多站雷达数字光纤传输系统设计

提出一种多站雷达体系雷达数据光纤传输系统的方案设计和实现方法。与传统雷达使用的光纤传输系统不同,而是采用技术较新的基于无源光网络PON的实时数据通信系统,这是无源光网络技术在多传感器实时通信领域的首次应用。在系统设计中利用先进的光电子和在编程技术,实现了点对多点雷达数据光纤传输,提高了信号传输质量,同时系统具有动态接入和扩容的能力。     

L波段掺铒光纤放大器增益钳制及提高特性研究

报道了一种新型980 nm激光二极管(LD)泵浦高增益的掺铒光纤放大器(EDFA).通过加入中心波长为1 550 nm光纤光栅(FBG)可以明显提高增益,并分析了增益钳制的原理.实验得到其增益比无FBG结构EDFA提高8 dB,并得到了小信号输入时增益25 dB的有效钳制.     

A case study in bio-inspired engineering design: defense applications of exoskeletal sensors

As part of a bio-inspired design process, the authors examine exoskeletal sensors found in insects and their potential application to armor and hardened buildings. In this way, the outer hardening of a structure or vehicle would not limit the ability of occupants to arrive at an actionable picture of the outer environment. To this end, various sensor modalities employed by insects are compared and contrasted with their current human-engineered equivalents. In several sensing modalities, biosensors perform better, are smaller, and more energy efficient than human-engineered equivalents. They note that biological designs tend to employ non-linear response to signal amplitude and respond with heightened sensitivity over a greater dynamic range of signals than human-engineered sensors. The insect biological sensors have structural and mechanical innovations that preserve the protective capacity of the exoskeleton.     

LDO稳压器敏感度建模与仿真技术研究

基于LDO稳压器在电磁干扰（EMI）下产生直流偏移失效的机理分析,展开敏感度建模与仿真方法研究。使用一款实验芯片,创新地引入片上电压传感器,用于测试EMI在LDO稳压器内部的传播特性。在敏感度建模中,建立等效电路模型,通过直流功能测试,Z参数阻抗特性测试验证模型的正确性,将该模型用于LDO稳压器的敏感度预测。在敏感度仿真过程中,通过分析关键子电路和不断增加寄生元件,仿真不同寄生因素对敏感度影响的权重。将仿真结果与传导直接注入法（DPI）片上测试结果对比,仿真结果与DPI测试在频域1MHz至1GHz匹配。     

基于WSN的目标探测与分类算法

针对WSN监测系统的目标检测与分类问题,提出一种基于直觉模糊推理(IFR)的多源数据融合方法。由模糊推理的思想,设计各状态变量的属性函数。根据目标声强变化和引起的地磁场变化的模型,设计模糊推理规则,并检验了所建规则的合理性。理论分析与仿真结果的对比表明算法能准确地对目标进行分类,且运算量小,适用于计算能力较弱的WSN节点。     

基于CC253O的烟雾传感器节点设计与实现

随着社会发展对消防安全的要求越来越高,实时地采集传输监测数据变得至关重要Ⅲ。本文针对现存的烟雾传感器节点可靠性差、准确率低、电路复杂,不易组网,并且在很多特定区域无法安装等问题,提出了基于CC2530的烟雾监测节点设计方案,并完成了以CC2530射频芯片为核心的烟雾传感器节点的硬、软件设计。实验测试证明,该节点满足无线消防监测系统的需要,具有高可靠性、低功耗以及低成本的特点,有着较好的应用前景。